HDB Interior Design Singapore: Pasir Ris TV Feature Wall Real Examples
HDB interior design Singapore homeowners in Pasir Ris often ask for a TV feature wall that hides cables and stores toys at the same time. The town has a mix of older resale flats and newer BTO blocks near the MRT, so the examples below come from both. Each wall had to follow HDB rules on hacking and load-bearing walls while fitting a 4-room or 5-room footprint.
How HDB interior design Singapore appears in Pasir Ris flats
Pasir Ris is a family town with many 5-room flats of about 110 sqm, which give enough living room width for a full feature wall. HDB interior design Singapore in this town leans practical: parents want a clean front for the TV and open storage behind for kids. The examples below show three real approaches that passed the HDB renovation permit without structural changes.
A 4-room Pasir Ris BTO with a full-height laminate wall
This BTO flat kept the original HDB floor tiles in the wet areas and built a full-height laminate feature wall in the living room. The wall ran 3.6 metres wide and 2.7 metres high, with a recessed TV niche and two flush cabinets on each side. The owner chose a light oak laminate so the small 90 sqm living room felt brighter. No structural wall was hacked because the feature wall was added carpentry fixed to the existing slab.
The carpenter built a 200 millimetre deep niche for the 55 inch TV and ran the cables through a back panel into a narrow service cavity. The result is a flat front with no visible wires and a slim console below for the set-top box.
A resale flat using a cantilever console to save floor space
An older Pasir Ris resale had a narrower living room, so the owner skipped floor cabinets and used a cantilever console fixed to the wall. The TV sat on a floating shelf while a shallow 150 millimetre ledge held the router and a plant. HDB flat space saving worked here because the floor stayed clear for a toddler to play. The wall behind got a simple two-tone paint, not full carpentry, which kept the cost down.
- The console was anchored into a timber stud wall, not the HDB structural wall.
- Cables dropped through a 40 millimetre chase into the built-in TV cabinet below.
- A pull-out drawer in the console held the game console and remotes.
A study nook built into the feature wall
One 5-room family asked for a study nook inside the feature wall so the children could do homework near the parents. The carpenter split the wall into a TV zone on the left and a fold-down desk on the right with open shelves above. When the desk is up, the living room looks like a normal feature wall. When it drops, two kids sit side by side.
- Measure the children's seat height and set the desk at 740 millimetres.
- Add a power point inside the nook for laptops, planned before the permit.
- Use soft-close hinges so the desk does not slam into the wall.
- Paint the nook a calm colour so it reads as a quiet corner.
Materials that pass HDB rules
Laminate and veneer are the safe choices for a feature wall because they are light and do not add load to the slab. Quartz or solid-surface cladding works for a small section behind the TV but must be fixed with approved anchors. HDB approved flooring like vinyl runs up to the wall base, and the feature wall sits on top without touching the structural elements.
Avoid heavy stone slabs across a full wall in an old resale, as the floor slab may not take the weight without an engineer's check. Your HDB Licensed Renovation Contractor will flag this during the permit drawing.
These Pasir Ris examples show that a TV feature wall can be a storage system, a study corner, or a simple calm surface depending on your flat and your family. A whole-house customization plan treats the wall as part of the living room, the storage, and the cabling at once, so the result fits your daily life instead of a showroom photo. Talk to a design team that knows HDB rules and can draw the wall, the power points, and the carpentry as one approved plan.
